Such conductors shall be separated at not less than 150 mm 6 in other than for monorail hoists where a spacing of not less than 75 mm 3 in shall be permitted. The conductor insulation shall be of a type that is approved for the voltage operating temperature and location of use.
Pin Su Colorado
Where the conductor material is not specified the material and the sizes given in this Code shall apply to copper conductors.
. Conductors normally used to carry current shall be of copper unless otherwise provided in this Code. Conductors other than flexible cords flexible cables and fixture wires shall be protected against overcurrent in accordance with their ampacities specified in 31014 unless otherwise permitted or required in 2404 A through G. Conductors normally used to carry current shall be of _____ unless otherwise provided in this Code.
The service disconnecting means shall plainly indicate whether it is in the open or closed position and shall be installed at a readily accessible location nearest the point of entrance of the service-entrance conductors. Where other materials are used the size shall be changed accordingly. Where the conductor material is not specified the.
EBJs shall not be connected to a terminal bar provided for grounded conductors unless the terminal bar is ____ for the purpose and otherwise permitted. See 1017 Examination of Equipment for Safety and 11013 Examination Identification Installation and Use of Equipment. A durable marking on the surface shall be provided at intervals not exceeding 24 inches by which the maker may be identified.
Main contact conductors carried along runways shall be supported on insulating supports placed at intervals not exceeding 60 m 20 ft unless otherwise permitted in 61021 F. See definitions of Approved Identified Labeled and Listed. Conductors of circuits rated over 1000 volts nominal shall not occupy the same equipment wiring enclosure cable or raceway with conductors of circuits rated 1000 volts nominal or less unless otherwise permitted in 3003C2a through 3003C2d.
In concealed knob and tube wiring clearance of not less than 26 mm shall be maintained between conductors the surface over which is passes. For copper-clad aluminum conductors see 31015. Conductors normally used to carry current shall be of copper unless otgherwise provided in this Code.
Where the conductor material is not specified the sizes given in this Code shall apply to copper conductors. Conductors normally used to carry current shall be of copper or aluminum unless otherwise provided in this Code. The conductors and equipment required or permitted by this Code shall be acceptable only if approved.
2404 Protection of Conductors. Frames of electric clothes dryers may be grounded by connection to the grounded circuit conductor only when this copper conductor is not smaller than and it is an existing branch circuit. Copper Where the conductor material is not specified the material and the sizes given in this Code shall apply to _____ conductors.
A Primary leads of electric-discharge lamp ballasts insulated for the primary voltage of. Where the driving machine or the motor-generator set is located in a remote machinery space a single means for disconnecting all ungrounded main power supply conductors shall be provided and be capable of being locked in the open position. G Overcurrent Protection for Specific Conductor Applica tions.
Where other materials are used the size shall be changed accordingly. 2404 Protection of Conductors. Means shall be provided to disconnect all conductors in a building or other structure from the service-entrance conductors.
All conductors used for general wiring shall be insulated unless otherwise permitted in these safety orders. Where the conductor material is not specified the sizes given in this code shall apply to copper conductors. See ICEA P-32-382-2007 R2013 Short Circuit Characteristics of Insulated Cables for information.
Such marking shall be the manufacturers name trade-mark. Insulated conductors for use at 600 volts or less shall conform to the provisions of Table 310-2b. Grounding conductors shall not be connected to a terminal bar provided for grounded conductors may be a neutral unless the bar is identified for the purpose and is located where connection is made from the grounded conductor to a grounding electrode as permitted or required by Article 250.
The manually operated switch shall be installed adjacent to this equipment. Where other materials are used the size shall be changed accordingly. After such 30-day period Conductor shall have no obligation to maintain or provide any Customer Content and shall thereafter unless legally prohibited delete all Customer Content in Conductors systems the Systems or otherwise in its possession or control.
One system grounded conductor shall have an outer covering conforming to 2006A or B 2 The grounded. Knob and tube wiring splices shall be soldered unless approved devices are used. Conductors other than flexible cords flexible cables and fixture wires shall be protected against overcurrent in accordance with their ampacities specified in 31014 unless otherwise permitted or required in 2404 A through G.
Unless otherwise permitted or required in 2404A through G. For aluminum and copper-clad aluminum conductors see. Overcurrent protection for the specific conductors shall be permitted to be provided as referenced in Table 2404G.
Conductors normally used to carry current shall be of copper or aluminum unless otherwise provided in this code. Conductors normally used to carry current shall be of copper or aluminum unless otherwise provided in this Code. A clearance of not less than 76 mm shall be maintained between conductors in concealed knob and tube wiring.
If there are three wires of 150 mm 2 connected to one terminal entering a cabinet or a switchboard the bending space at each terminal shall NOT be less than ____ provided the conductors do not enter or leave the enclosure through the wall opposite its terminals. Where the conductor material is not specified the material and the sizes given in this Code shall apply to copper conductors.
Pin On Florence And Cripple Creek Railway
Pin On Report Template
02 042 Warning Labels Vinyl Labels Power Source
0 Comments